Even with my torque based controller DS1 was ridiculously difficult.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Quote from: HornetMaX on May 06, 2019, 11:28:34 AMThe question would be: why would you do that ? Expect for the obvious "I've lost my right hand".Hahahaaa
Quote from: D4rw1n on May 05, 2019, 07:44:19 PMTotally agreeing (and btw I like this Alcatraz example )
Root cause why I haven't voted yet, as my only experience so far is with lean angle input & an xbox controller ... but I'm not liking it from the first day as it's not natural at all.
Quote from: HornetMaX on May 05, 2019, 06:57:00 PMWith a joypad (or, more precisely, without force feedback) DSA/DST make no sense.
You should address this only at people with FFB devices.
Saying "I tried DST/DSA with a joypad and it didn't work" is like saying you tried to dig yourself out of alcatraz with a toothpick and you didn't enjoy it. It's expected.
Quote from: poupou59890 on May 03, 2019, 12:07:17 PMFor the clutch, front break and rear brake (not clutch at this time I am waiting to check everything else before buying a complete set for the clutch) I use cheap chinese set of hydraulic lever on Aliexpress, than transducer (500 and 1000psi) in order to traanform the pressure apply to a signal between 0-5V. Here again, just plug everythign and that's it. https://www.aliexpress.com/item/Motobike-Racing-bike-lever-handle-bar-brake-pump-hydraulic-clutch-set-kit-17-5-piston-cylinder/32718100514.html
and for the pressure transducer : https://www.ebay.com/itm/Stainless-Steel-Pressure-transducer-sender-for-oil-fuel-air-water-100psi-2500psi-/172780141579
Quote from: poupou59890 on May 03, 2019, 12:07:17 PMFor the gear shift, I need to finish this one. I use real motorbike shifter from China (same set than the rear brake with master cylinder and pressure transudcer), I think I will use 2 buttons and put a screw next to each one in order to be sure that it will be the screw to stop the foot peg and not the button to avoid breaking it.
Quote from: poupou59890 on May 03, 2019, 12:07:17 PMSo for now I have every parts, I have use a cbr 600 rr template on Solidworks in order to draw my "chassis" with exact same dimension than a real one bike and I use direct steering with angle in order to be as real as it can. hope it will workSounds really ambitious! Can't wait to see it take form!
and if eveything is perfect I will try to use a 2DOF air sim balance system in order to add real lean thanks to GPbikes data ouptut. but I am no there yet. Hope it can help.
Even is the leabodnard is a bit pricey (around 60 euros) it is very easy to use, no driver, just plug eveything at the right place, put the usb and that's it.
Quote from: speedfr on May 03, 2019, 12:06:25 PMNews coming soon i hope...
Quote from: MultiCOOLFRESH on May 03, 2019, 10:52:52 AMWhat do you exactly mean
Quote from: MultiCOOLFRESH on May 03, 2019, 09:59:16 AMThank you guys for the kind support
I will just have a detailled look at what you wrote to me and research this Leonardo thing
Quote from: TimboC137 on May 03, 2019, 09:56:03 AM@Chris_Beeves what is the leonardo's resolution for analog axes? I think it's 8-bit (255 steps), but I'm not sure. The leo bodnar board is 12-bit (4096 steps), so it might be the better choice. Although it is much more expensive.